1. Wheel Bearings
Over time, wheel bearings suffer the effects of wear and tear. Water in particular takes its toll on them, making then rust or spoiling the grease that surrounds them. Wheel bearings allow your wheels to turn smoothly and also support the weight of the vehicle. If you're noticing alignment problems, your wheels are making a rumbling sound or the steering seems to have too much 'play' then you may have a wheel bearing problem and they may not be doing their job correctly. For quality wheel bearings for any car, check on line at eurocarparts.com and head off the danger of serious damage before it's too late.
http://ball-bearings.online
2. Hot Forming
Hot forging is the plastic deformation of metal at a temperature and strain rate such that recrystallization occurs simultaneously with deformation, thus avoiding strain hardening. For this to occur, high workpiece temperature (matching the metal's recrystallization temperature) must be attained throughout the process. A form of hot forging is isothermal forging, where materials and dies are heated to the same temperature. In nearly all cases, isothermal forging is conducted on superalloys in a vacuum or highly controlled atmosphere to prevent oxidation.
http://hot-forming.ktforge.co.uk
3. Press Forging
Press forging works by slowly applying a continuous pressure or force, which differs from the near-instantaneous impact of drop-hammer forging. The amount of time the dies are in contact with the workpiece is measured in seconds (as compared to the milliseconds of drop-hammer forges). The press forging operation can be done either cold or hot. The main advantage of press forging, as compared to drop-hammer forging, is its ability to deform the complete workpiece. Drop-hammer forging usually only deforms the surfaces of the workpiece in contact with the hammer and anvil; the interior of the workpiece will stay relatively undeformed. Another advantage to the process includes the knowledge of the new part's strain rate. We specifically know what kind of strain can be put on the part, because the compression rate of the press forging operation is controlled.
http://www.kt-forge.co.uk/press-forging
4. Simply Bearings
With the premier SKF brand your requirement for high quality bearings are here. Naturally we supply other quality brands like NACHI, NTN, KOYO, NKE, UBC, FAG, INA, IKO,NIS, TIMKEN etc and have in excess of 35,000 products listed here. We are ISO9001:2008 official bearings and seal distributors and suppliers and are official IKO distributors. Secure Online Transactions with HSBC Card Payment Services, Paypal and Google Checkout. ISO 9001:2008 Quality Managed and Accredited. Simply Bearings Ltd The UK's Original Online Bearings and Seals suppliers.
http://ball-bearings.online
5. Needle Roller Bearings
Needle roller bearings are roller bearings with cylindrical rollers that are small in diameter. In spite of their low cross section, needle roller bearings have a high load carrying capacity and are therefore extremely suitable for bearing arrangements where radial space is limited. SKF supplies needle roller bearings in different designs and a wide range of sizes, which are appropriate for different applications. In addition to customized designs, they comprise the following types and components: needle roller and cage assemblies); drawn cup needle roller bearings; with open ends and with a closed end; full complement with open ends; needle roller bearings with machined rings; with flanges (closure rings or integral flanges) on the outer ring, sealed or not sealed and with or without an inner ring; without flanges on the outer ring , not sealed and with or without an inner ring; alignment needle roller bearings; with and without an inner ring ; inner rings for needle roller bearings ; universal joint bearings ; needle rollers; combined needle roller bearings (separate section); needle roller / angular contact ball bearings ; needle roller / thrust ball bearings ; needle roller / cylindrical roller thrust bearings ; needle roller thrust bearings and bearing washers (separate section); needle roller and cage thrust assemblies and appropriate washers; needle roller thrust bearings with a centring spigot and appropriate washers.
http://ball-bearings.online
6. Chesterfield Custom Software
Custom software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.chesterfield.custom.software.grid-itc.com
7. Open Source
1T Solutions install and support linux based open source solutions and systems to small and medium businesses across Rotherham, Sheffield, Barnsley, Doncaster, Chesterfield and across South Yorkshire.
http://open-source.1t-s.com
8. Cold Forging
Cold forging is a high speed manufacturing process whereby metal is shaped at room temperature often without the need for the removal of material. A simple blank is placed within a die and a punch is pressed into the blank. The blank then takes on the form of the punch and the die. By utilising multiple dies and punches in succession very complex shapes can be achieved. Metal is forced beyond its yield (elastic) limit and retains its altered shape upon removal from the die. The metal is not forced beyond its tensile strength, otherwise fracturing would occur (the exception is when trimming or piercing). Historically cold forming has been an experienced based technology, but this is changing as new computer based analytical tools are constantly being developed.
http://cold-forging.kt-forge.co.uk
9. Mercedes Benz Car Bearings
Mercedes-Benz, a German luxury automobile manufacturer, offers a diverse range of car models to cater to various segments and customer preferences. Mercedes-Benz car models include A-Class (entry-level compact car), C-Class (compact executive car), E-Class (mid-size luxury car), S-Class (full-size luxury sedan), GLE-Class (mid-size luxury SUV), GLC-Class (compact luxury SUV), GLA-Class (compact luxury SUV designed for urban environments), GLS-Class (full-size luxury SUV with three rows of seating), G-Class (or "G-Wagon" is a legendary off-road luxury SUV) and AMG Models (high-performance division of Mercedes-Benz). Mercedes-Benz regularly introduces new models and updates existing ones. The availability of specific models may vary by region and time.
http://ball-bearings.online/oem/merc/products
10. Doncaster Bespoke Software
Bespoke software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://doncaster.bespoke.software.grid-itc.com
11. Smith Forging
Forging worked between flat or simple contour dies by repeated strokes and manipulation of the workpiece. Also known as "hand" or "flat die " forging.Heavy workpieces could be processed using a smith-forging hammer, and smaller forgings are die formed in drop hammers. Smith forging hammers are typically steam or air-operated, consisting of a power actuated ram supported by a heavy cast iron frame. The final product is a result of the ram being powered into the dies containing the workpiece.
http://smith-forging.ktforge.co.uk
12. Rotherham Computer Services
Computer service and support across Rotherham, Sheffield, Doncaster and Barnsley. 1T Solutions Ltd offer cost effective computer maintenance for small and medium businesses.
http://www.rotherham.computer.service.1t-s.com
13. 316 Stainless Steel
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://www.zx55.com
14. Scooter Bearings
If you have plastic core scooter wheels then fitting the bearings is very straight forward as they typically can be pushed in by hand without issue. Fitting scooter bearings into Metal core wheels is a little trickier as they are designed to be a tight fit so pushing them in by hand rarely works. In our workshop we used to use a vise to gently squeeze them in, but now we use a hammer!! Apply a small amount of grease to the edges of each bearing you are going to install. Apply a small amount of grease to the inside hole on the scooter wheel where the bearings are going to be fitted. Place the bearing over the hole in the wheel and try and make sure that it is straight/level as possible. Place either a block of wood or an old paperback book over the top of the bearing and gently strike this with the hammer (Important - do not strike the bearing directly with the hammer). When the bearing has been hammered in fully into the hole in the middle of your wheel it should sit flush with the edge of the wheel Turn the wheel over and insert the bearing spacer (you will need a bearing spacer, if you do not use one your wheel will not spin when you do your axles up securely!)
http://ball-bearings.online
15. Software Development
Software development services, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.software-development.1tsolutions.com
16. Doncaster Application Development
Computer applications software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.doncaster.application.development.abrt.com
17. House For Rent Huddersfield
4 Bedroom house to share: Student accomodation available to rent near Huddersfield University. House with four bedrooms to let with common sitting-room, shared kitchen and batchroom with over the bath shower. Two of the rooms have on suite toilet and wash basin. The house is located in the Paddock area of Huddersfield, post code HD1 and is 1.4 miles from the University, 1.2 miles from the Huddersfield train station. The house is on a regular bus route, buses 301a, 302 (every 15 minutes) and 302a.
http://house-for-rent-huddersfield.iam4share.co.uk/
18. Steel Forging
Virtually all metals that can be moulded / drawn out may be forged by first heating and then hammering it in to the desired shape. A billet, wrought bar, cast or sintered ingot etc.. may be forged. Forging improves the toughness and strength of improving orientation of the metal grain structure. The repeated heating and hammering causes the metal to become more dense and the grain "flow lines" to follow the contour of the end product.
http://www.kt-forge.co.uk/steel-forging
19. Drop Forging
Drop forging is a metal shaping process, the metal to be formed is first heated then shaped by forcing it into the contours of a die, this force can be in excess of 2000 tons. The drop forging process can be performed with the material at various temperatures. Hot Forging: During hot forging the metals are heated to above their recrystallization temperature. The main benefit of this hot forging is that work hardening is prevented due to the recrystallization of the metal as it begins to cool. Cold Forging: Cold Forging is generally performed with metal at room temperature below the the recrystallization temperature. Cold forging typically work hardens the metal. There are two types of drop forging, open die and closed die. Open die drop forging requires the operator to position the work piece while it is impacted by the ram. The die attached to the ram is usually flat or of a simple contour, most of the shaping is achieved by the operator physically positioning the work piece before each stroke of the ram. There are also special dies which can be used to cut the metal, form holes or notches.
http://drop-forging.ktforge.co.uk
20. Bespoke Software
Bespoke software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.bespoke-software.1tsolutions.com
21. Sheffield Computer Services
Computer service and support across Rotherham, Sheffield, Doncaster and Barnsley. 1T Solutions Ltd offer cost effective computer maintenance for small and medium businesses.
http://sheffield.computer.service.1t-s.com
22. Web Design
Professional and creative web design services. We build web sites for businesses across South Yorkshire, Rotherham, Sheffield, Doncaster and Barnsley. From a simple brochure to e-commerce with advanced dynamic content features, we can build the web site t promote your business on-line.
http://1t-s.com/web-design
23. Computer Support
Computer service and support across Rotherham, Sheffield, Doncaster and Barnsley. 1T Solutions Ltd offer cost effective computer maintenance for small and medium businesses.
http://www.abrt.com/computer-support
24. 304 Stainless Steel
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://304.stainless-steel.zx55.com
25. Huddersfield University Accomodation
4 Bedroom house to share: Student accomodation available to rent near Huddersfield University. House with four bedrooms to let with common sitting-room, shared kitchen and batchroom with over the bath shower. Two of the rooms have on suite toilet and wash basin. The house is located in the Paddock area of Huddersfield, post code HD1 and is 1.4 miles from the University, 1.2 miles from the Huddersfield train station. The house is on a regular bus route, buses 301a, 302 (every 15 minutes) and 302a.
http://www.student-housing-huddersfield.co.uk/
26. Stainless Steel Gaskets
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://www.zx55.com
27. Axle Bearings
Because axle shafts are typically made of softer steel than bearing rollers, shafts have a tendency to wear out before the bearing. The rollers can actually wear away a section of the shaft, as shown in the below diagram. Automotive cylindrical axle repair bearings are designed to replace the original bearings and seals on axles that are still in good condition, but whose original bearing and/or seal contact paths are not suitable for continued use. The extra-wide bearing repositions the rollers and seal to ride on unworn portions of the axle closer to the flange. Lubrication is accomplished through the axle tube by differential fluid, just like the OE design.
http://ball-bearings.online
28. Stainless Steel Low Pressure Fittings
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://zx55.com
29. Low Pressure Fittings
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://low-pressure-fittings.stainless-steel.zx55.com
30. Stainless Steel Fittings
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://www.fittings.stainless-steel.zx55.com
31. Weldolets
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://www.zx55.com
32. South Yorkshire Bespoke Software
Bespoke software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.south-yorkshire.bespoke.software.abrt.com
33. Skip Manager
Skip Manager has been designed to enable you to manage the hire of your skips more effectively. From the initial bookings, hire, tracking and collections to credit control, Skip Manager has the functionality required for your Waste Recycling business.
http://skip-manager.com
34. Doncaster Application Development
Computer applications software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://doncaster.application.development.1t-s.com
35. Timeken
Timken Bearing Products. Timken is a leader in all bearing types, including standard anti-friction bearing configurations and advanced products such as housed units, integrated bearing assemblies, precision assemblies and FAA-approved aerospace bearings. Timken Roller Bearings, Tapered Roller Bearings, Spherical Roller Bearings, Cylindrical Roller Bearings, Precision Cylindrical Roller Bearings, Needle Roller Bearings, Thrust Roller Bearings, Timken Ball Bearings, Radial Ball Bearings, Angular Contact Bearings, Precision Bearings, Timken Spherical Plain Bearings, Radial Bearings, Radial Bearings with Lip Seals, Angular Contact Thrust Bearings, Timken High Performance Bearings, AquaSpexx® Trailer Wheel Bearing Kits, AquaSpexx® for Industrial Applications, DuraSpexx® and DuraSpexx® Power Rating Series, Thin Dense Chrome Bearings, Debris Resistant Bearings, Wear-Resistant Bearings, Low Torque Bearings, P900 Bearings, Timken Precision Bearings for Machine Tools, Super Precision Ball Bearings, Precision Tapered Roller Bearings, Ball Screw Support Bearings, Hydra-Rib Variable Preload Bearings, Precision Crossed Roller Bearings, Precision Cylindrical Roller Bearings, Timken Aerospace Bearings, Aerospace Ball Bearings, Aerospace Cylindrical Bearings, Aerospace Tapered Roller Bearings, Aerospace Spherical Roller Bearings, Aircraft Landing Wheel Bearings, Timken Integrated Bearing Assemblies, AP™ Integrated Bearing Assemblies, AP-2™ Integrated Bearing Assemblies, Formed Hub Wheel End System.
http://ball-bearings.online
36. Student Accomodation Huddersfield
4 Bedroom house to share: Student accomodation available to rent near Huddersfield University. House with four bedrooms to let with common sitting-room, shared kitchen and batchroom with over the bath shower. Two of the rooms have on suite toilet and wash basin. The house is located in the Paddock area of Huddersfield, post code HD1 and is 1.4 miles from the University, 1.2 miles from the Huddersfield train station. The house is on a regular bus route, buses 301a, 302 (every 15 minutes) and 302a.
http://www.iam4rent.co.uk/
37. House to Share Huddersfield
4 Bedroom house to share: Student accomodation available to rent near Huddersfield University. House with four bedrooms to let with common sitting-room, shared kitchen and batchroom with over the bath shower. Two of the rooms have on suite toilet and wash basin. The house is located in the Paddock area of Huddersfield, post code HD1 and is 1.4 miles from the University, 1.2 miles from the Huddersfield train station. The house is on a regular bus route, buses 301a, 302 (every 15 minutes) and 302a.
http://www.student-housing-huddersfield.co.uk/
38. Waste Collection Software
Skip Manager has been designed to enable you to manage the hire of your skips more effectively. From the initial bookings, hire, tracking and collections to credit control, Skip Manager has the functionality required for your Waste Recycling business.
http://www.waste-collection-software.skip-manager.co.uk
39. Doncaster Bespoke Software
Bespoke software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://doncaster.bespoke.software.abrt.com
40. Custom Software
Custom software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://custom.software.grid-itc.com
41. Self-aligning ball bearings
The self-aligning ball bearing was invented by SKF. It has two rows of balls and a common concave sphered raceway in the outer ring. The bearing is consequently self-aligning and insensitive to angular misalignments of the shaft relative to the housing. It is particularly suitable for applications where considerable shaft deflections or misalignment are to be expected. Additionally, the self-aligning ball bearing has the lowest friction of all rolling bearings, which enables it to run cooler even at high speeds. SKF produces self-aligning ball bearings to several designs. These are open bearings of the basic design, sealed bearings, open bearings with an extended inner ring.
http://ball-bearings.online?pg=rb-sabb
42. Bearing and Housing Units
Tapered bearings, also known as tapered roller bearings, are a type of rolling element bearing that can support both radial and axial loads. They are designed with tapered inner and outer races and tapered rollers. The shape of the co>
http://ball-bearings.online/categories/bearing-and-housing-units?id_category=13
43. Chesterfield Custom Software
Custom software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.chesterfield.custom.software.1t-s.com
44. Koyo Bearings
KOYO brand bearings from JTEKT are found virtually anywhere where accurate rotational control is required. Bearing applications vary from jet engine main shaft support, manufacturing equipment used to produce semiconductors and LCD displays, through modern windmills, automobiles, high-speed trains and agricultural machinery to medical equipment, drilling machines at your dentist's surgery and various appliances at your household. We are proud to say: our bearings are found from the heights of the stratosphere to the depths of the ocean - many specially developed to function with optimum efficiency in harsh environments such as weightless or extremely corrosive conditions. In short, you will find Koyo bearings wherever there is a need for innovative engineering and reliability that will last.
http://ball-bearings.online
45. Hot Forming
Hot forging is the plastic deformation of metal at a temperature and strain rate such that recrystallization occurs simultaneously with deformation, thus avoiding strain hardening. For this to occur, high workpiece temperature (matching the metal's recrystallization temperature) must be attained throughout the process. A form of hot forging is isothermal forging, where materials and dies are heated to the same temperature. In nearly all cases, isothermal forging is conducted on superalloys in a vacuum or highly controlled atmosphere to prevent oxidation.
http://www.kt-forge.co.uk/hot-forming
46. Barnsley Custom Software
Custom software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.barnsley.custom.software.abrt.com
47. Custom Software
Custom software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://custom.software.1t-s.com
48. Software Development
Software development services, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://software.development.abrt.com
49. Application Development
Computer applications software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.abrt.com/application-development
50. South Yorkshire Application Development
Computer applications software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.south-yorkshire.application.development.grid-itc.com
51. Chesterfield Software Development
Software Development, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://chesterfield.software.devlopment.1t-s.com
52. Hot Forging
Hot forging is the plastic deformation of metal at a temperature and strain rate such that recrystallization occurs simultaneously with deformation, thus avoiding strain hardening. For this to occur, high workpiece temperature (matching the metal's recrystallization temperature) must be attained throughout the process. A form of hot forging is isothermal forging, where materials and dies are heated to the same temperature. In nearly all cases, isothermal forging is conducted on superalloys in a vacuum or highly controlled atmosphere to prevent oxidation.
http://hot-forging.ktforge.co.uk
53. Sheffield Application Development
Computer applications software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://sheffield.application-development.1tsolutions.com
54. 316 Stainless Steel
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://zx55.com
55. Sheffield Software Development
Software Development, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.sheffield.software.devlopment.1tsolutions.com
56. South Yorkshire Application Development
Computer applications software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://south-yorkshire.application.development.grid-itc.com
57. Stainless Steel Forging
Virtually all metals that can be moulded / drawn out may be forged by first heating and then hammering it in to the desired shape. A billet, wrought bar, cast or sintered ingot etc.. may be forged. Forging improves the toughness and strength of improving orientation of the metal grain structure. The repeated heating and hammering causes the metal to become more dense and the grain "flow lines" to follow the contour of the end product.
http://stainless-steel-forging.kt-forge.co.uk
58. Student Accomodation Huddersfield
4 Bedroom house to share: Student accomodation available to rent near Huddersfield University. House with four bedrooms to let with common sitting-room, shared kitchen and batchroom with over the bath shower. Two of the rooms have on suite toilet and wash basin. The house is located in the Paddock area of Huddersfield, post code HD1 and is 1.4 miles from the University, 1.2 miles from the Huddersfield train station. The house is on a regular bus route, buses 301a, 302 (every 15 minutes) and 302a.
http://student-accomodation-huddersfield.iam4share.co.uk/
59. Renault Car Bearings
Renault is a French automotive manufacturer known for producing a wide range of cars, from compact hatchbacks to SUVs and electric vehicles such as the Renault Clio (compact hatchback), Renault Megane (family hatchback), Renault Captur (compact crossover SUV), Renault Kadjar (mid-size SUV), Renault Duster (compact SUV), Renault Zoe (all-electric compact car), (mid-size sedan) and Renault Twingo (small city car). Renault also offers other models such as the Renault Scenic (MPV), Renault Koleos (SUV), and the Renault Espace (large crossover). The company continues to innovate and expand its range with a focus on electric and hybrid vehicles, as well as advanced connectivity and autonomous driving technologies.
http://ball-bearings.online/oem/renault/products
60. Sheffield Bespoke Software
Bespoke software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.sheffield.bespoke.software.grid-itc.com
61. Huddersfield University Student Accomodation
4 Bedroom house to share: Student accomodation available to rent near Huddersfield University. House with four bedrooms to let with common sitting-room, shared kitchen and batchroom with over the bath shower. Two of the rooms have on suite toilet and wash basin. The house is located in the Paddock area of Huddersfield, post code HD1 and is 1.4 miles from the University, 1.2 miles from the Huddersfield train station. The house is on a regular bus route, buses 301a, 302 (every 15 minutes) and 302a.
http://www.iam4share.co.uk/huddersfield-university-student-accomodation
62. Skip Hire System
Skip Manager has been designed to enable you to manage the hire of your skips more effectively. From the initial bookings, hire, tracking and collections to credit control, Skip Manager has the functionality required for your Waste Recycling business.
http://www.skip-hire-software.skip-manager.co.uk
63. South Yorkshire Open Source
1T Solutions install and support linux based open source solutions and systems to small and medium businesses across Rotherham, Sheffield, Barnsley, Doncaster, Chesterfield and across South Yorkshire.
http://south-yorkshire.open-source.1t-s.com
64. South Yorkshire Linux
1T Solutions install and support linux based open source solutions and systems to small and medium businesses across Rotherham, Sheffield, Barnsley, Doncaster, Chesterfield and across South Yorkshire.
http://south-yorkshire.linux.1t-s.com
65. Custom Software
Custom software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.abrt.com/custom-software
66. Linear Bearings
Inch linear bearings and shafting. SKF offers a full line of inch linear bearings and shafting. The linear bearings are available in closed or open style, standard or self-aligning, as well as mounted in a variety of housing styles. We also offer a line of precision ground inch shafting for use with the linear bearings. Shafting is available cut to length to meet your requirements, predrilled and tapped, or per your custom print. SKF Inch Linear Bearings. SKF offers a complete line of inch linear ball bearings: open, closed and housed units available for quick delivery in sizes 1/8" to 4". SKF Inch Shafting. Standard case hardened Class L and Class S shafting available cut to length. Sizes from ¼" diameter to 2" diameter, as well as standard predrilled and tapped shafting, shaft supports and shaft blocks are available for quick delivery.
http://ball-bearings.online
67. Sheffield Bespoke Software
Bespoke software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.sheffield.bespoke.software.abrt.com
68. Online Bearings
Online Bearings. Totally refreshing concept to the way you purchase your bearings and power transmission products. With experience in the bearing industry, we aim to provide the best quality product at the best possible price. We carry from stock all types of bearings, including deep groove ball bearings, roller bearings, metric and imperial bearings, tapered roller bearings, spherical bearings and needle bearings - plus many more. We also stock all types of chains and sprockets, taper bushes, oil seals and O-rings, airline fittings, braided hose, oils, greases and lubricants, as well as all types of lubrication equipment. In addition, we supply industrial tools, V-belts and wedge belts, timing belts and HTD belts and also offer a belt making service for all types of flat belts. Our preferred brands of bearings and power transmission products are from leading manufacturers, but we have an extensive range of cheaper alternatives in our budget section for customers who wish to keep their costs to a minimum.
http://ball-bearings.online
69. Computer Services
Computer service and support across Rotherham, Sheffield, Doncaster and Barnsley. 1T Solutions Ltd offer cost effective computer maintenance for small and medium businesses.
http://computer.service.1t-s.com
70. Roll Forging
Roll forging is a process where round or flat bar stock is reduced in thickness and increased in length. Roll forging is performed using two cylindrical or semi-cylindrical rolls, each containing one or more shaped grooves. A heated bar is inserted into the rolls and when it hits a stop the rolls rotate and the bar is progressively shaped as it is rolled through the machine. The piece is then transferred to the next set of grooves or turned around and reinserted into the same grooves. This continues until the desired shape and size is achieved. The advantage of this process is there is no flash and it imparts a favorable grain structure into the workpiece. Examples of products produced using this method include axles, tapered levers and leaf springs.
http://www.kt-forge.co.uk/roll-forging
71. Doncaster Software Development
Software Development, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.doncaster.software.devlopment.1tsolutions.com
72. South Yorkshire Software Development
Software Development, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.south-yorkshire.software.devlopment.1tsolutions.com
73. Sockolets
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://www.sockolets.zx55.com
74. South Yorkshire Application Development
Computer applications software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://south-yorkshire.application.development.abrt.com
75. Doncaster eCommerce
Professional and creative web design services. We build web sites for businesses across South Yorkshire, Rotherham, Sheffield, Doncaster and Barnsley. From a simple brochure to e-commerce with advanced dynamic content features, we can build the web site t promote your business on-line.
http://www.1t-s.com/internet-web-design
76. Forging Stainless Steel
Virtually all metals that can be moulded / drawn out may be forged by first heating and then hammering it in to the desired shape. A billet, wrought bar, cast or sintered ingot etc.. may be forged. Forging improves the toughness and strength of improving orientation of the metal grain structure. The repeated heating and hammering causes the metal to become more dense and the grain "flow lines" to follow the contour of the end product.
http://forging-stainless-steel.ktforge.co.uk
77. Chesterfield Bespoke Software
Bespoke software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://chesterfield.bespoke.software.1t-s.com
78. South Yorkshire Application Development
Computer applications software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://south-yorkshire.application-development.1tsolutions.com
79. Skip Hire Software
Skip Manager has been designed to enable you to manage the hire of your skips more effectively. From the initial bookings, hire, tracking and collections to credit control, Skip Manager has the functionality required for your Waste Recycling business.
http://www.skip-hire-software.skip-manager.co.uk
80. Cold Forging
Cold forging is a high speed manufacturing process whereby metal is shaped at room temperature often without the need for the removal of material. A simple blank is placed within a die and a punch is pressed into the blank. The blank then takes on the form of the punch and the die. By utilising multiple dies and punches in succession very complex shapes can be achieved. Metal is forced beyond its yield (elastic) limit and retains its altered shape upon removal from the die. The metal is not forced beyond its tensile strength, otherwise fracturing would occur (the exception is when trimming or piercing). Historically cold forming has been an experienced based technology, but this is changing as new computer based analytical tools are constantly being developed.
http://cold-forging.ktforge.co.uk
81. Stainless Steel Valves
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://valves.stainless-steel.zx55.com
82. Threadolets
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://zx55.com
83. Computer Services
Computer service and support across Rotherham, Sheffield, Doncaster and Barnsley. 1T Solutions Ltd offer cost effective computer maintenance for small and medium businesses.
http://1t-s.com/computer-services
84. Rotherham Bespoke Software
Bespoke software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.rotherham.bespoke.software.1t-s.com
85. Stainless Tube Supplier
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://zx55.com
86. Stainless Steel Low Pressure Fittings
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://www.low-pressure-fittings.stainless-steel.zx55.com
87. Sockolets
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://www.zx55.com
88. South Yorkshire Bespoke Software
Bespoke software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://south-yorkshire.bespoke.software.grid-itc.com
89. Stainless Steel Flanges
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://www.flanges.stainless-steel.zx55.com
90. Stainless Steel Low Pressure BSP Fittings
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://www.zx55.com
91. Student Diggs in Huddersfield
4 Bedroom house to share: Student accomodation available to rent near Huddersfield University. House with four bedrooms to let with common sitting-room, shared kitchen and batchroom with over the bath shower. Two of the rooms have on suite toilet and wash basin. The house is located in the Paddock area of Huddersfield, post code HD1 and is 1.4 miles from the University, 1.2 miles from the Huddersfield train station. The house is on a regular bus route, buses 301a, 302 (every 15 minutes) and 302a.
http://student-diggs-huddersfield.iam4share.co.uk/
92. Msajid Message Display Board
Masjid Message Display Boad, Salah Times, Clock, Islamic calendar and message display board software program for PCs designed specially for Masjids and Mosques. Suitable for Jamat Times, Salah Timetable, Namaz Times, Salaat Times. Free Download.
http://masjid-message-display-board.jamat-times.com
93. Sealed Bearings
Sealed bearings. A selection of SKF spherical roller bearings is also produced in a sealed version with contact seals on both sides. The seals are reinforced with sheet steel and made of an oil and wear-resistant: acrylonitrile-butadiene rubber (NBR), designation suffix 2CS; hydrogenated acrylonitrile butadiene rubber (HNBR), designation suffix 2CS5; fluoro rubber (FKM), designation suffix 2CS2. The seals are inserted in recesses in the outer ring. For smaller bearing sizes, the seals are pressed into the recesses while the seals for the larger sizes are held in position by means of retaining rings (fig). The seals have two sealing lips contacting the lead-in at the sides of the inner ring raceway, to provide efficient sealing. Sealed bearings are lubricated as standard with an extreme pressure bearing grease according to table 1. They should not be heated to temperatures above 80°C during mounting, and should not be washed. Sealed bearings do not need to be relubricated when the operating temperature does not exceed 70°C and the rotational speed is below 50% of the limiting speed listed in the product table. When temperature and/or speeds are high, relubrication with a similar grease with lithium thickener is recommended. In this case the polymer band, which covers the lubrication holes in the outer ring must be removed before mounting. Note that only a small amount of grease is needed to relubricate sealed bearings. The grease should be pressed in slowly through the lubrication holes in the outer ring while the bearing is rotating. Excessive pressure should be avoided so as not to damage the seals. The internal design of a sealed bearing corresponds to that of an open bearing. The external dimensions are also the same except for bearings based on the 222 and 223 series. These bearings are slightly wider and carry the series designation BS2-22 and BS2-23 respectively. Sealed bearings are available with a cylindrical bore as standard. However most bearings in the BS2-22 series are available with a tapered bore as well. Every sealed bearing can be supplied with a tapered bore to special order. To prevent interference with the seal, the diameter of the shaft abutment should not exceed damax at least for the 1 to 2 mm closest to the bearing. If the bearings are secured axially on the shaft by a lock nut, SKF recommends using a KMFE lock nut or to position an intermediate ring between the bearing and the lock nut.
http://ball-bearings.online
94. Waste Recycling Software
Skip Manager has been designed to enable you to manage the hire of your skips more effectively. From the initial bookings, hire, tracking and collections to credit control, Skip Manager has the functionality required for your Waste Recycling business.
http://waste-recycling-software.skip-manager.com
95. Chesterfield Linux
1T Solutions install and support linux based open source solutions and systems to small and medium businesses across Rotherham, Sheffield, Barnsley, Doncaster, Chesterfield and across South Yorkshire.
http://chesterfield.linux.1t-s.com
96. Doncaster Software Development
Software Development, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://doncaster.software.devlopment.1t-s.com
97. Stainless Steel Valves
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://www.zx55.com
98. Swaging
T=Swaging is a forging process in which the dimensions of an item are altered using a die or dies, into which the item is forced. Swaging is usually a cold working process; however, it is sometimes done as a hot working process. Virtually all metals that can be moulded / drawn out may be forged by first heating and then hammering it in to the desired shape. A billet, wrought bar, cast or sintered ingot etc.. may be forged. Forging improves the toughness and strength of improving orientation of the metal grain structure. The repeated heating and hammering causes the metal to become more dense and the grain "flow lines" to follow the contour of the end product.
http://www.kt-forge.co.uk/swaging
99. Waste Recycling Software
Skip Manager has been designed to enable you to manage the hire of your skips more effectively. From the initial bookings, hire, tracking and collections to credit control, Skip Manager has the functionality required for your Waste Recycling business.
http://waste-recycling-software.skip-manager.co.uk
100. Software Development
Software development services, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.1tsolutions.com/software-development
101. Gatekeeper
A spam filtering service suitable for small and medium businesses, the 1T Solutions Gatekeeper service is competitively priced, and removes over 95% of e-mail spam and viruses.
http://www.1t-s.com/gatekeeper
102. Y-bearings with a tapered bore
Y-bearings in the YSA 2-2FK series have an inner ring extended on both sides and a tapered bore (taper 1:12) enabling them to be mounted on standard adapter sleeves in the H 23 series. The appropriate adapter sleeve is not part of the bearing and must be ordered separately. Y-bearings of this type are delivered exclusively with the rugged standard "Superagriseal" fitted with additional plain sheet steel flingers. The outer ring has two lubrication holes as standard. Mounting onto an adapter sleeve enables the bearings to operate at higher speeds, run more smoothly in applications where the direction of rotation is constant or alternating. The SKF range, which comprises bearings with bore diameter from 25 to 65 mm, fits adapter sleeves in the H 23 series for metric shafts ranging from 20 to 60 mm. These bearings can also be used on adapter sleeves in the HA 23, HE 23 and HS 23 series for inch shafts ranging from 3/4 to 2 3/8 inch diameter.
http://ball-bearings.online?pg=rb-yb-tb
103. Custom Software
Custom software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.1t-s.com/custom-software
104. Barnsley Bespoke Software
Bespoke software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.barnsley.bespoke.software.grid-itc.com
105. Business Accounting Software
Business accounting software that you can download for free and start using immediately. Features include: Sales Quotes, Sales Order Processing, Sales Invoicing, Purchase Order Processing, Goods Received, Full Stock Control with emphasis on traceability, Nominal Ledger and much more...
http://iceledger.com/
106. Computer Services
Computer service and support across Rotherham, Sheffield, Doncaster and Barnsley. 1T Solutions Ltd offer cost effective computer maintenance for small and medium businesses.
http://www.computer.service.1t-s.com
107. Software Development
Software development services, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://software-development.1tsolutions.com
108. South Yorkshire Software Development
Software Development, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://south-yorkshire.software.devlopment.1t-s.com
109. Stainless Steel Tubing
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://www.zx55.com
110. Doncaster Application Development
Computer applications software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://doncaster.application-development.1tsolutions.com
111. Stainless Steel Pipes
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://www.pipes.stainless-steel.zx55.com
112. ball-bearings.online
Bearings are mechanical components used to enable smooth and controlled motion between two or more parts. They are designed to reduce friction and support loads, allowing rotating or linear movement with minimal resistance. The primary function of a bearing is to facilitate the relative motion between two parts, typically a rotating shaft and a stationary housing or structure. By providing a low-friction interface between these parts, bearings enable efficient transfer of loads and motion. They are essential components in various machines and mechanical systems, ranging from small devices to large industrial equipment.
http://ball-bearings.online
113. ZX55.com
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://www.zx55.com
114. Student Diggs in Huddersfield
4 Bedroom house to share: Student accomodation available to rent near Huddersfield University. House with four bedrooms to let with common sitting-room, shared kitchen and batchroom with over the bath shower. Two of the rooms have on suite toilet and wash basin. The house is located in the Paddock area of Huddersfield, post code HD1 and is 1.4 miles from the University, 1.2 miles from the Huddersfield train station. The house is on a regular bus route, buses 301a, 302 (every 15 minutes) and 302a.
http://student-diggs-huddersfield.iam4rent.co.uk/
115. South Yorkshire Custom Software
Custom software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.south-yorkshire.custom.software.grid-itc.com
116. Rotherham Application Development
Computer applications software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://rotherham.application.development.abrt.com
117. Stainless Steel Flanges
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://www.zx55.com
118. Waste Management Software
Skip Manager has been designed to enable you to manage the hire of your skips more effectively. From the initial bookings, hire, tracking and collections to credit control, Skip Manager has the functionality required for your Waste Recycling business.
http://www.waste-management-software.skip-manager.com
119. Waste Recycling Software
Skip Manager has been designed to enable you to manage the hire of your skips more effectively. From the initial bookings, hire, tracking and collections to credit control, Skip Manager has the functionality required for your Waste Recycling business.
http://www.waste-recycling-software.skip-manager.com
120. Stainless Steel Valves
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://www.valves.stainless-steel.zx55.com
121. Steel Forging
Virtually all metals that can be moulded / drawn out may be forged by first heating and then hammering it in to the desired shape. A billet, wrought bar, cast or sintered ingot etc.. may be forged. Forging improves the toughness and strength of improving orientation of the metal grain structure. The repeated heating and hammering causes the metal to become more dense and the grain "flow lines" to follow the contour of the end product.
http://www.kt-forge.co.uk/steel-forging
122. Chesterfield Application Development
Computer applications software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://chesterfield.application.development.grid-itc.com
123. Huddersfield University Accomodation
4 Bedroom house to share: Student accomodation available to rent near Huddersfield University. House with four bedrooms to let with common sitting-room, shared kitchen and batchroom with over the bath shower. Two of the rooms have on suite toilet and wash basin. The house is located in the Paddock area of Huddersfield, post code HD1 and is 1.4 miles from the University, 1.2 miles from the Huddersfield train station. The house is on a regular bus route, buses 301a, 302 (every 15 minutes) and 302a.
http://www.iam4rent.co.uk/huddersfield-university-accomodation
124. Rotherham Application Development
Computer applications software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://rotherham.application-development.1tsolutions.com
125. Doncaster Software Development
Software Development, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://doncaster.software.devlopment.grid-itc.com
126. Hygienic Fittings
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://zx55.com
127. South Yorkshire Software Development
Software Development, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.south-yorkshire.software.devlopment.1t-s.com
128. Rotherham Web Design
Professional and creative web design services. We build web sites for businesses across South Yorkshire, Rotherham, Sheffield, Doncaster and Barnsley. From a simple brochure to e-commerce with advanced dynamic content features, we can build the web site t promote your business on-line.
http://rotherham.web-design.1t-s.com
129. Self Lube Bearings
A self-lubricating bearing, also known as a self-lube bearing or a maintenance-free bearing, is a type of bearing that does not require external lubrication to reduce friction and support loads. These bearings are designed with built-in lubrication systems or materials that provide continuous or intermittent lubrication during operation. A self-lubricating bearing, also known as a self-lube bearing or a maintenance-free bearing, is a type of bearing that does not require external lubrication to reduce friction and support loads. These bearings are designed with built-in lubrication systems or materials that provide continuous or intermittent lubrication during operation.
http://ball-bearings.online/categories/self-lube-bearings?id_category=11
130. Trailer Bearings
Trailer Bearings for all types of boat trailers - both tapered roller and ball bearings. The most popular bearings fitted to trailers are Tapered Roller Bearings. They come as two separate parts called the cup and cone. Some are supplied with a seal built in as an integral part of the bearing cone. Most bearings are stamped with an identification number by the manufacturer, If there are no numbers then the bearing can be identified by its dimensions - try typing the sizes in the search box. The most common bearings used on boat trailers are L44643 - L44610 and L44643L - L44610 Bearing number L44643 refers to the bearing cone without built in seal as shown on the left in both pictures. Bearing number L44643 L refers to the bearing cone with built in seal as shown on the right in both pictures. The same cup is used for both having the number L44610. Bearings for old style Mini hubs - these use ball bearings of the type 14/LJT 7/8" The bearings are a single row thrust bearing - 2" outside x 7/8" bore x 9/16" wide There are usually two bearings per hub with an oilseal which is 2.1/8" x 1.3/8" x 5/16".We supply both the bearings and oilseal - see our Online shop for prices.
http://ball-bearings.online
131. Custom Software
Custom software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://custom.software.abrt.com
132. Chesterfield Bespoke Software
Bespoke software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.chesterfield.bespoke-software.1tsolutions.com
133. Barnsley Custom Software
Custom software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://barnsley.custom.software.grid-itc.com
134. House to Share Huddersfield
4 Bedroom house to share: Student accomodation available to rent near Huddersfield University. House with four bedrooms to let with common sitting-room, shared kitchen and batchroom with over the bath shower. Two of the rooms have on suite toilet and wash basin. The house is located in the Paddock area of Huddersfield, post code HD1 and is 1.4 miles from the University, 1.2 miles from the Huddersfield train station. The house is on a regular bus route, buses 301a, 302 (every 15 minutes) and 302a.
http://www.iam4share.co.uk/house-to-share-huddersfield
135. Stainless Steel Hygienic Fittings
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://www.hygienic-fittings.stainless-steel.zx55.com
136. General Motors Car Bearings
General Motors (GM) cars also use a variety of bearings in different parts of their vehicles, such as Wheel Bearings, Crankshaft Bearings, Transmission Bearings, Differential Bearings, Idler Bearings and Tensioner Bearings. Just like with Ford cars, it's important to consider the specific model, year, and components of a GM vehicle when selecting replacement bearings. Referring to the vehicle's service manual or consulting with a qualified mechanic is recommended to ensure the correct bearings are chosen.
http://ball-bearings.online/oem/gmc/products
137. Barnsley Bespoke Software
Bespoke software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.barnsley.bespoke.software.abrt.com
138. Needle Roller Bearings
A needle roller bearing is a type of rolling element bearing that uses long, thin cylindrical rollers with a small diameter in proportion to their length. These rollers, known as needle rollers, have a high length-to-diameter ratio, giving them a needle-like appearance and name. Needle roller bearings are designed to support high radial loads with a relatively small cross-sectional area. Needle roller bearings are commonly used in various applications that require compact and lightweight designs with high load-carrying capacity. They are found in automotive transmissions, power tools, motorcycles, industrial machinery, and other equipment where space constraints and high load requirements are present.
http://ball-bearings.online/categories/needle-roller?id_category=17
139. Barnsley Linux
1T Solutions install and support linux based open source solutions and systems to small and medium businesses across Rotherham, Sheffield, Barnsley, Doncaster, Chesterfield and across South Yorkshire.
http://barnsley.linux.1t-s.com
140. Doncaster Custom Software
Custom software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://doncaster.custom.software.grid-itc.com
141. Accounts Software for Stockists
Designed for steel stock holders, SASS is a muli-currency accounts system which is ideal for all stockists incorporating Sales, Purchase & Nominal ledgers, Stock Control with emphasis traceability and profits based on actual / real costs ...
http://steelaccounts.com/
142. Student Accomodation in Huddersfield
4 Bedroom house to share: Student accomodation available to rent near Huddersfield University. House with four bedrooms to let with common sitting-room, shared kitchen and batchroom with over the bath shower. Two of the rooms have on suite toilet and wash basin. The house is located in the Paddock area of Huddersfield, post code HD1 and is 1.4 miles from the University, 1.2 miles from the Huddersfield train station. The house is on a regular bus route, buses 301a, 302 (every 15 minutes) and 302a.
http://www.iam4rent.co.uk/student-accomodation-huddersfield
143. Sheffield Software Development
Software Development, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://sheffield.software.devlopment.1t-s.com
144. Skip Manager
Skip Manager has been designed to enable you to manage the hire of your skips more effectively. From the initial bookings, hire, tracking and collections to credit control, Skip Manager has the functionality required for your Waste Recycling business.
http://www.skip-manager.co.uk
145. South Yorkshire Custom Software
Custom software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://south-yorkshire.custom.software.grid-itc.com
146. Triumph Motor Vehicle Bearings
The history of the Triumph brand spans over a century and includes a rich legacy in the motorcycle and automobile industries. The Triumph brand was founded in 1885 by Siegfried Bettmann, a German immigrant, in Coventry, England. Initially, Triumph focused on manufacturing bicycles and bicycle parts. The company quickly gained popularity and expanded its production capacity. In 1902, Triumph produced its first motorcycle, a 2.2 horsepower model powered by a Belgian Minerva engine. After World War II, Triumph concentrated solely on motorcycle production and became one of the most prominent motorcycle manufacturers in the world. The 1950s and 1960s were a golden era for Triumph motorcycles, with iconic models like the Triumph Bonneville, Triumph Tiger, and Triumph Trident gaining widespread popularity. Triumph motorcycles achieved considerable success in racing, including victories at the Isle of Man TT races and other prestigious competitions. In the 1970s, Triumph faced financial difficulties and changing market dynamics, which led to the closure of its motorcycle division in 1983. However, the Triumph brand was resurrected in 1984 when businessman John Bloor acquired the rights to the name and established Triumph Motorcycles Ltd. Under Bloor's leadership, Triumph underwent a revival, focusing on modernizing its product lineup, improving quality, and leveraging its heritage. Triumph Motorcycles Ltd. re-entered the motorcycle market in 1990 and has since become a prominent player in the industry. The company expanded its product range, offering a diverse lineup of motorcycles across various categories, including cruisers, sport bikes, adventure bikes, and modern classics. Triumph has gained recognition for its distinctive designs, advanced engineering, and performance-oriented motorcycles.
http://ball-bearings.online/oem/triumph/products
147. Open Die Forging
Open-die forging is also known as smith forging. In open-die forging, a hammer strikes and deforms the workpiece, which is placed on a stationary anvil. Open-die forging gets its name from the fact that the dies (the surfaces that are in contact with the workpiece) do not enclose the workpiece, allowing it to flow except where contacted by the dies. Therefore the operator needs to orient and position the workpiece to get the desired shape. The dies are usually flat in shape, but some have a specially shaped surface for specialized operations. For example, a die may have a round, concave, or convex surface or be a tool to form holes or be a cut-off tool. Open-die forging lends itself to short runs and is appropriate for art smithing and custom work. In some cases, open-die forging may be employed to rough-shape ingots to prepare them for subsequent operations. Open-die forging may also orient the grain to increase strength in the required direction. Cogging is successive deformation of a bar along its length using an open-die drop forge. It is commonly used to work a piece of raw material to the proper thickness.
http://open-die-forging.ktforge.co.uk
148. Stainless Pipe Supplier
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://zx55.com
149. Open Source
1T Solutions install and support linux based open source solutions and systems to small and medium businesses across Rotherham, Sheffield, Barnsley, Doncaster, Chesterfield and across South Yorkshire.
http://www.open-source.1t-s.com
150. Huddersfield University Accomodation
4 Bedroom house to share: Student accomodation available to rent near Huddersfield University. House with four bedrooms to let with common sitting-room, shared kitchen and batchroom with over the bath shower. Two of the rooms have on suite toilet and wash basin. The house is located in the Paddock area of Huddersfield, post code HD1 and is 1.4 miles from the University, 1.2 miles from the Huddersfield train station. The house is on a regular bus route, buses 301a, 302 (every 15 minutes) and 302a.
http://huddersfield-university-accomodation.iam4share.co.uk/
151. Hub Bearings
Wheel Bearings & Hubs. Over time, wheel bearings suffer the effects of wear and tear. Water in particular takes its toll on them, making then rust or spoiling the grease that surrounds them. Wheel bearings allow your wheels to turn smoothly and also support the weight of the vehicle. If you're noticing alignment problems, your wheels are making a rumbling sound or the steering seems to have too much 'play' then you may have a wheel bearing problem and they may not be doing their job correctly. For quality wheel bearings for any car, check on line at ball-bearings.online and head off the danger of serious damage before it's too late.
http://ball-bearings.online
152. Doncaster Application Development
Computer applications software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://doncaster.application.development.grid-itc.com
153. Student Accomodation Huddersfield
4 Bedroom house to share: Student accomodation available to rent near Huddersfield University. House with four bedrooms to let with common sitting-room, shared kitchen and batchroom with over the bath shower. Two of the rooms have on suite toilet and wash basin. The house is located in the Paddock area of Huddersfield, post code HD1 and is 1.4 miles from the University, 1.2 miles from the Huddersfield train station. The house is on a regular bus route, buses 301a, 302 (every 15 minutes) and 302a.
http://www.iam4share.co.uk/
154. Sheffield Application Development
Computer applications software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://sheffield.application.development.grid-itc.com
155. Waste Management System
Skip Manager has been designed to enable you to manage the hire of your skips more effectively. From the initial bookings, hire, tracking and collections to credit control, Skip Manager has the functionality required for your Waste Recycling business.
http://waste-management-system.skip-manager.com
156. Bespoke Software
Bespoke software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.grid-itc.com/bespoke-software
157. Software Development
Software development services, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://grid-itc.com/software-development
158. Stainless Steel
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://stainless-steel.zx55.com
159. Chesterfield Custom Software
Custom software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://chesterfield.custom.software.abrt.com
160. Hygienic Fittings
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://www.hygienic-fittings.stainless-steel.zx55.com
161. Doncaster Open Source
1T Solutions install and support linux based open source solutions and systems to small and medium businesses across Rotherham, Sheffield, Barnsley, Doncaster, Chesterfield and across South Yorkshire.
http://doncaster.open-source.1t-s.com
162. Huddersfield University Accomodation
4 Bedroom house to share: Student accomodation available to rent near Huddersfield University. House with four bedrooms to let with common sitting-room, shared kitchen and batchroom with over the bath shower. Two of the rooms have on suite toilet and wash basin. The house is located in the Paddock area of Huddersfield, post code HD1 and is 1.4 miles from the University, 1.2 miles from the Huddersfield train station. The house is on a regular bus route, buses 301a, 302 (every 15 minutes) and 302a.
http://www.iam4share.co.uk/huddersfield-university-accomodation
163. Application Development
Computer applications software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.1t-s.com/application-development
164. Bespoke Software
Bespoke software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://grid-itc.com/bespoke-software
165. SKF Bearings
Steel City Bearings are one of the worlds leading suppliers of all bearing and transmission products. Steel City Bearings Ltd can offer the following to all its customers: Massive stocks of all leading brands * Same day despatch on ALL stock items * Over 100 years of bearing and transmission knowledge * Highly competitive pricing * Friendly and reliable sales team * Over 25,000 lines and 250,000 items in stock * Next day delivery to mainland UK including Northern Ireland
http://www.steelcitybearings.com
166. Sheffield Bespoke Software
Bespoke software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.sheffield.bespoke.software.1t-s.com
167. Doncaster Linux
1T Solutions install and support linux based open source solutions and systems to small and medium businesses across Rotherham, Sheffield, Barnsley, Doncaster, Chesterfield and across South Yorkshire.
http://www.doncaster.linux.1t-s.com
168. High Pressure Fittings
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://high-pressure-fittings.stainless-steel.zx55.com
169. IT Support
Computer service and support across Rotherham, Sheffield, Doncaster and Barnsley. 1T Solutions Ltd offer cost effective computer maintenance for small and medium businesses.
http://www.1t-s.com/service
170. Hammer Forging
The most common type of forging equipment is the hammer and anvil. Principles behind the hammer and anvil are still used today in drop-hammer equipment. The principle behind the machine is simple: raise the hammer and drop it or propel it into the workpiece, which rests on the anvil. The main variations between drop-hammers are in the way the hammer is powered; the most common being air and steam hammers. Drop-hammers usually operate in a vertical position. The main reason for this is excess energy (energy that isn't used to deform the workpiece) that isn't released as heat or sound needs to be transmitted to the foundation. Moreover, a large machine base is needed to absorb the impacts. To overcome some shortcomings of the drop-hammer, the counterblow machine or impactor is used. In a counterblow machine both the hammer and anvil move and the workpiece is held between them. Here excess energy becomes recoil. This allows the machine to work horizontally and have a smaller base. Other advantages include less noise, heat and vibration. It also produces a distinctly different flow pattern. Both of these machines can be used for open-die or closed-die forging. A forging press, often just called a press, is used for press forging.
http://www.kt-forge.co.uk/hammer-forging
171. SKF Bearings
Steel City Bearings are one of the worlds leading suppliers of all bearing and transmission products. Steel City Bearings Ltd can offer the following to all its customers: Massive stocks of all leading brands * Same day despatch on ALL stock items * Over 100 years of bearing and transmission knowledge * Highly competitive pricing * Friendly and reliable sales team * Over 25,000 lines and 250,000 items in stock * Next day delivery to mainland UK including Northern Ireland
http://www.steelcitybearings.com
172. Sheffield Application Development
Computer applications software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://sheffield.application.development.1t-s.com
173. RHP Bearings
RHP Bearings. RHP is a part of NSK Ltd. and is a key producer of high quality bearings. NSK Ltd. (RHP) has been around since 1916, when it was originally established in Japan. RHP bearings are some of the best bearings available on a global scale, manufactured by a renowned bearings company to the utmost quality. RHP bearings are available from Nationwide Bearings at fantastic prices - so get your RHP bearings today and make the most of our quick, convenient delivery services. RHP bearings are widely available thanks to their high quality and you can order them from zx55.com Bearings all at competitive prices. Whether you're simply looking for one or two types of RHP bearings for some repairs and maintenance work or are a manufacturer needing to stock up on supplies, we're ready to take your RHP bearing orders and quickly deliver them to you. We also stock plenty of bearings from other manufacturers, such as Timken bearings, FAFNIR bearings, INA bearings, FAG bearings and Torrington bearings, so you can be sure you'll be able to find exactly what you're looking for. We take pride in our work, which is why you can always trust that ordering bearings from zx55.com Bearings will be quick, simple and reliable. We'll pack your order with care before posting it direct to your door, ensuring a stress-free experience when you order your new bearings online.
http://ball-bearings.online
Application Development - Chesterfield Bespoke Software - Drop Forging - South Yorkshire Software Development - Stainless Steel Fittings - South Yorkshire Custom Software
Roll Forging - Sheffield Bespoke Software - Threadolets - Doncaster Web Design - Software Development - Low Pressure Fittings
Student Accomodation in Huddersfield - Rotherham Bespoke Software - Computer Support - 304 Stainless Steel - Bespoke Software - Doncaster Custom Software
Custom Software - 304 Stainless Steel - Stainless Steel Flanges - Computer Repair - Domain WhoIs - Chesterfield Bespoke Software
Barnsley Custom Software - Sheffield Linux - Chesterfield Software Development - Rotherham Software Development - Ball Bearings - Custom Software
Chesterfield Application Development - Sheffield Software Development - Forging - Single row deep groove ball bearings - Waste Management System - Computer Repair
Chesterfield Custom Software - Rotherham Software Development - Bearing Puller - Open Die Forging - Stainless Steel Low Pressure BSP Fittings - South Yorkshire Software Development
Salat Timings - Cold Forming - Chesterfield Application Development - South Yorkshire Open Source - Timeken - Engine Bearings
Doncaster Software Development - Msajid Message Display Board - Swaging - Linux - Jaguar Car Bearings - Sheffield Open Source
South Yorkshire Software Development - Steel Forging - Surplus Bearings - Rotherham Software Development - Doncaster Application Development - Computer Support
Rooms For Rent Huddersfield - Chesterfield Linux - Huddersfield University Accomodation - Stainless Steel Forging - Custom Software - Rooms For Rent Huddersfield
Sanitary Fittings - Waste Recycling Software - Triumph Motor Vehicle Bearings - Student Accomodation Huddersfield - Huddersfield Student Housing - Iveco Truck Bearings
South Yorkshire Bespoke Software - Doncaster Custom Software - Waste Management System - Doncaster Open Source - Stainless Steel Valves - High Pressure Fittings
Deep groove ball bearings with filling slots - Roll Forging - Salaat Times - Bespoke Software - Student Accomodation in Huddersfield - Stainless Pipe Supplier
Waste Collection System - Student Diggs in Huddersfield - Chesterfield Custom Software - South Yorkshire Software Development - Sanitary Fittings - Bespoke Software
Sanitary Fittings - Wheel Bearings - Bearings By Size - Open Die Forging - bearings direct - Doncaster Bespoke Software
Rooms For Rent Huddersfield - Custom Software - Waste Management System - Stainless Steel Low Pressure Fittings - Barnsley Bespoke Software - Doncaster Custom Software
Stainless Steel Flange Gaskets - 316 Stainless Steel - Steel City Bearings - Software Development - Sheffield Bespoke Software - Stainless Steel Flanges
Needle Bearings - Rotherham Computer Services - Tapered Roller Bearings - Stainless Steel Valves - Motorcycle Bearings - Sheffield Application Development
Web Design - Rotherham Bespoke Software - Chesterfield Application Development - Barnsley Computer Services - Student Accomodation Huddersfield - Huddersfield University Accomodation
Chesterfield Computer Services - Custom Software - Bespoke Software - Doncaster Software Development - Rotherham Bespoke Software - Barnsley Software Development
Smith Forging - Steel Forging - Custom Software - Huddersfield University Student Accomodation - Waste Management Software - Doncaster Application Development
South Yorkshire Application Development - Software Development - Sheffield Custom Software - Self Lube Bearings - Web Design - SKF Bearings
South Yorkshire Bespoke Software - Waste Management Software - Hot Forming - Y-bearings with a hexagonal or square bore - Spherical Roller Bearings - Inner Rings
Doncaster Linux - Stainless Tube Supplier - Stainless Steel Low Pressure Fittings - Bulk Bearings - Sheffield Software Development - Stainless Steel Forging
Barnsley Bespoke Software - Smith Forging - Stainless Steel Flanges - House For Rent Huddersfield - Doncaster Bespoke Software - Student Accomodation Huddersfield
Press Forging